Network cheat sheet
From Wikitech
(Difference between revisions)
LeslieCarr (Talk | contribs) |
m (Krinkle moved page Network Cheat Sheet to Network cheat sheet: Casing) |
||
| (One intermediate revision by one user not shown) | |||
| Line 1: | Line 1: | ||
| − | =Foundry= | + | == Foundry == |
| − | + | Unlike juniper all operational (like show) commands work in configuration mode. | |
| + | |||
Foundries don't take ssh keys and need passwords. boo! | Foundries don't take ssh keys and need passwords. boo! | ||
| + | <pre> | ||
show interfaces brief - shows interfaces with status, speed, and description (port-name) | show interfaces brief - shows interfaces with status, speed, and description (port-name) | ||
Port Link L2 State Dupl Speed Trunk Tag Priori MAC Name | Port Link L2 State Dupl Speed Trunk Tag Priori MAC Name | ||
| Line 34: | Line 36: | ||
unt eth X/X - puts X/X into that vlan as untagged | unt eth X/X - puts X/X into that vlan as untagged | ||
no unt eth X/x - takes X/X out of vlan | no unt eth X/x - takes X/X out of vlan | ||
| − | + | </pre> | |
| + | |||
if you get the error "error - port ethe 1/25 do not belong to default vlan" that means the port is in another vlan and must be removed first | if you get the error "error - port ethe 1/25 do not belong to default vlan" that means the port is in another vlan and must be removed first | ||
| − | =Juniper= | + | == Juniper == |
| − | + | ||
Junipers take ssh keys. huzzah! | Junipers take ssh keys. huzzah! | ||
| − | |||
| + | Juniper has operational mode and configuration mode. | ||
| + | |||
| + | <pre> | ||
operational mode - | operational mode - | ||
{master:8} | {master:8} | ||
| Line 49: | Line 53: | ||
{master:8}[edit] | {master:8}[edit] | ||
lcarr@asw-a-eqiad# | lcarr@asw-a-eqiad# | ||
| − | + | </pre> | |
== Operational commands == | == Operational commands == | ||
| + | <pre> | ||
show ethernet-switching table - shows mac addresses | show ethernet-switching table - shows mac addresses | ||
show ethernet-switching table interface - shows mac addresses for that interface | show ethernet-switching table interface - shows mac addresses for that interface | ||
| Line 65: | Line 70: | ||
show log messages | last 20 - shows log with info | show log messages | last 20 - shows log with info | ||
| + | </pre> | ||
| − | == Config commands == | + | === Config commands === |
Junipers configure after you confirm - you can configure and then double check | Junipers configure after you confirm - you can configure and then double check | ||
| − | configure - puts you in config mode | + | * configure - puts you in config mode |
| − | exit - takes you up one level (or out of) config mode | + | * exit - takes you up one level (or out of) config mode |
| − | top - takes you to the top level of config mode | + | * top - takes you to the top level of config mode |
| − | + | * show - shows you configuration below that level | |
| − | show - shows you configuration below that level | + | |
Latest revision as of 08:37, 27 February 2013
Contents |
[edit] Foundry
Unlike juniper all operational (like show) commands work in configuration mode.
Foundries don't take ssh keys and need passwords. boo!
show interfaces brief - shows interfaces with status, speed, and description (port-name) Port Link L2 State Dupl Speed Trunk Tag Priori MAC Name 1/1 Up Forward Full 1G None No level0 0012.f2c5.5600 db63 1/2 Up Forward Full 1G None No level0 0012.f2c5.5600 db64 | include - grep sh mac-address - shows mac addresses sh mac-address ethernet x/x - shows mac for interface x/x conf t - configuration mode SSH@csw1-sdtpa(config)# show run - shows configuration int ether 12/1 - go into configuration for that interface port-name - assigns description disable - turns port off enable - turns port on exit - moves you up a level after configuration - ALWAYS type "write mem" must do write mem OUT of config mode write mem - saves to hard drive the config, incase the box reboots in conf mode - Foundries configure immediately - when you've typed the command, it's live! vlan 2 - moves into vlan 2's configuration mode unt eth X/X - puts X/X into that vlan as untagged no unt eth X/x - takes X/X out of vlan
if you get the error "error - port ethe 1/25 do not belong to default vlan" that means the port is in another vlan and must be removed first
[edit] Juniper
Junipers take ssh keys. huzzah!
Juniper has operational mode and configuration mode.
operational mode -
{master:8}
lcarr@asw-a-eqiad>
configuration mode -
{master:8}[edit]
lcarr@asw-a-eqiad#
[edit] Operational commands
show ethernet-switching table - shows mac addresses show ethernet-switching table interface - shows mac addresses for that interface show ethernet-switching table vlan - shows mac addresses for vlan show interfaces descriptions - Interface Admin Link Description ge-1/0/0 up up ms1001 show interfaces terse - shows interfaces with ip's in a very short format show interface ge-1/0/0 (extensive)- shows interfaces in more detail monitor interface xe-1/1/0 - shows interface in a real-time updating mode (errors, bits, etc) show log messages | last 20 - shows log with info
[edit] Config commands
Junipers configure after you confirm - you can configure and then double check
- configure - puts you in config mode
- exit - takes you up one level (or out of) config mode
- top - takes you to the top level of config mode
- show - shows you configuration below that level
