Network cheat sheet
From Wikitech
(Difference between revisions)
LeslieCarr (Talk | contribs) |
|||
| Line 1: | Line 1: | ||
| − | =Foundry= | + | == Foundry == |
| − | + | Unlike juniper all operational (like show) commands work in configuration mode. | |
| + | |||
Foundries don't take ssh keys and need passwords. boo! | Foundries don't take ssh keys and need passwords. boo! | ||
| + | <pre> | ||
show interfaces brief - shows interfaces with status, speed, and description (port-name) | show interfaces brief - shows interfaces with status, speed, and description (port-name) | ||
Port Link L2 State Dupl Speed Trunk Tag Priori MAC Name | Port Link L2 State Dupl Speed Trunk Tag Priori MAC Name | ||
| Line 34: | Line 36: | ||
unt eth X/X - puts X/X into that vlan as untagged | unt eth X/X - puts X/X into that vlan as untagged | ||
no unt eth X/x - takes X/X out of vlan | no unt eth X/x - takes X/X out of vlan | ||
| − | + | </pre> | |
| + | |||
if you get the error "error - port ethe 1/25 do not belong to default vlan" that means the port is in another vlan and must be removed first | if you get the error "error - port ethe 1/25 do not belong to default vlan" that means the port is in another vlan and must be removed first | ||
| − | =Juniper= | + | == Juniper == |
| − | + | ||
Junipers take ssh keys. huzzah! | Junipers take ssh keys. huzzah! | ||
| − | |||
| + | Juniper has operational mode and configuration mode. | ||
| + | |||
| + | <pre> | ||
operational mode - | operational mode - | ||
{master:8} | {master:8} | ||
| Line 49: | Line 53: | ||
{master:8}[edit] | {master:8}[edit] | ||
lcarr@asw-a-eqiad# | lcarr@asw-a-eqiad# | ||
| − | + | </pre> | |
== Operational commands == | == Operational commands == | ||
| + | <pre> | ||
show ethernet-switching table - shows mac addresses | show ethernet-switching table - shows mac addresses | ||
show ethernet-switching table interface - shows mac addresses for that interface | show ethernet-switching table interface - shows mac addresses for that interface | ||
| Line 65: | Line 70: | ||
show log messages | last 20 - shows log with info | show log messages | last 20 - shows log with info | ||
| + | </pre> | ||
| − | == Config commands == | + | === Config commands === |
Junipers configure after you confirm - you can configure and then double check | Junipers configure after you confirm - you can configure and then double check | ||
| − | configure - puts you in config mode | + | * configure - puts you in config mode |
| − | exit - takes you up one level (or out of) config mode | + | * exit - takes you up one level (or out of) config mode |
| − | top - takes you to the top level of config mode | + | * top - takes you to the top level of config mode |
| − | + | * show - shows you configuration below that level | |
| − | show - shows you configuration below that level | + | |
Revision as of 08:37, 27 February 2013
Contents |
Foundry
Unlike juniper all operational (like show) commands work in configuration mode.
Foundries don't take ssh keys and need passwords. boo!
show interfaces brief - shows interfaces with status, speed, and description (port-name) Port Link L2 State Dupl Speed Trunk Tag Priori MAC Name 1/1 Up Forward Full 1G None No level0 0012.f2c5.5600 db63 1/2 Up Forward Full 1G None No level0 0012.f2c5.5600 db64 | include - grep sh mac-address - shows mac addresses sh mac-address ethernet x/x - shows mac for interface x/x conf t - configuration mode SSH@csw1-sdtpa(config)# show run - shows configuration int ether 12/1 - go into configuration for that interface port-name - assigns description disable - turns port off enable - turns port on exit - moves you up a level after configuration - ALWAYS type "write mem" must do write mem OUT of config mode write mem - saves to hard drive the config, incase the box reboots in conf mode - Foundries configure immediately - when you've typed the command, it's live! vlan 2 - moves into vlan 2's configuration mode unt eth X/X - puts X/X into that vlan as untagged no unt eth X/x - takes X/X out of vlan
if you get the error "error - port ethe 1/25 do not belong to default vlan" that means the port is in another vlan and must be removed first
Juniper
Junipers take ssh keys. huzzah!
Juniper has operational mode and configuration mode.
operational mode -
{master:8}
lcarr@asw-a-eqiad>
configuration mode -
{master:8}[edit]
lcarr@asw-a-eqiad#
Operational commands
show ethernet-switching table - shows mac addresses show ethernet-switching table interface - shows mac addresses for that interface show ethernet-switching table vlan - shows mac addresses for vlan show interfaces descriptions - Interface Admin Link Description ge-1/0/0 up up ms1001 show interfaces terse - shows interfaces with ip's in a very short format show interface ge-1/0/0 (extensive)- shows interfaces in more detail monitor interface xe-1/1/0 - shows interface in a real-time updating mode (errors, bits, etc) show log messages | last 20 - shows log with info
Config commands
Junipers configure after you confirm - you can configure and then double check
- configure - puts you in config mode
- exit - takes you up one level (or out of) config mode
- top - takes you to the top level of config mode
- show - shows you configuration below that level
